Furnace Repair in New York
Attempting to fix your furnace on your own in New York, can be somewhat intimidating.
When your heat won’t come on, figuring out a furnace-related issue can seem like a big job. That need not, however, be the case.
You may save a furnace repair call with a few quick, inexpensive improvements you may make yourself.
Before you call an HVAC expert, try the troubleshooting list below if your furnace won’t start, won’t remain on, or wont ignite.
Living in New York and in need of assistance from a heating and conditioning expert? DARIO Contracting Inc. can help. We offer emergency furnace repair in addition to servicing most makes of heating systems.
Make an appointment to replace your furnace by calling 646-836-2936 right now.
We also install furnaces if your home is ready for a new heating system.
As you speak with us, think about putting together an annual furnace maintenance schedule that could prevent future malfunctions. We can recommend to you how often one of our NATE-certified experts should check your furnace.
Start troubleshooting your furnace with our simple guide below. Most of these procedures don’t call any mechanical knowledge.
Checklist of Furnace Repairs
Check Switches and Breakers
You will next need to make sure the furnace and breaker switches are turned on.
Find the principal electrical panel of your home. Look for a grey metal box in your closet, garage or basement if you’re not sure where it is.
Before handling the panel or breakers, be sure your hands and feet are dry.
Check that the breaker marked “furnace” or “heat” is turned “on.” The middle, or “off” position of the breaker will indicate a trip.
Firmly turn on the breaker with one hand. Leave the breaker alone if it trips right away and then returns to “off,” and give DARIO Contracting Inc.a call at +1 646-836-2936.
Whatever the age or make of your furnace, it has at least one standard wall switch on or close by.
Ensure the switch is turned to the “on” position. Should it have been switched off, allow up to five minutes for your furnace to come on. (If you’re not sure where your furnace is, look in your utility closet, garage, or basement. In an attic or crawl space, too.)
Remote Controlled Temperature
if the screen is blank, change the batteries. The thermostat could have to be changed if the digital screen is muddled.
Check that “heat” is the setting on the switch, not “off” or “cool.”
Verify the programme is set to “run” and is showing the right day and time. If the programme isn’t functioning, use the up/down arrows to adjust the temperature and then hit the “hold” button. Should thermostat programming be malfunctioning, this will compel the furnace to start.
Increase the temperature to five degrees above room temperature.
To check that your furnace is powered on, flip the fan switch from “auto” to “on” if it hasn’t started in a few minutes. Should the fan stop working, there may be a problem with your furnace.
Check the Thermostat
Make sure your thermostat is indicating to your furnace to turn on first.
Changing the Air Filter
Often the cause of furnace breakdowns is a dirty, blocked air filter.
Air Filter
If your filter is too dirty:
Your furnace won’t turn on at all or may overheat from inadequate ventilation.The more often your furnace runs, the higher your energy expenses may be.Because a dirty filter makes your furnace work harder, it may cease working too soon.A very filthy filter can trip the breaker and cut off the power to your furnace.Your air filter will be found inside the blower compartment of your furnace, an attached filter case or a wall-mounted return air grille, depending on the brand of furnace you own.
Changing your filter:
Shut down your furnace.Remove the filter, then tilt it towards the light. Change it out if you can’t see light through it.To prevent damage, install the replacement filter with the arrow facing the furnace.Pleated filters should last about three months, but flat filters should be changed every month. Additionally available is a washable filter that will last for roughly ten years. A new filter may need to be installed more frequently if you have kids or pets.To speed up the process going forward, write the airflow direction and filter size in permanent marker on your furnace housing or ductwork.
Check the Condensate Pan
Condensate pans, sometimes referred to as drain pans, store the water your furnace extracts from the air. Try these measures if your furnace is leaking water or if standing water is in its pan. Verify the drain on your pan is clear if it has one (look for a PVC pipe). If it has to be emptied, use a specific pan-cleaning tablet available at hardware or home improvement stores. Look over the float switch if your pan has a pump. Please call us at 646-836-2936 if the switch is “up” with liquid in the pan; you will most likely need a new pump.
Check for Furnace Error Codes
Should problems continue, check the blower motor’s condition by looking inside the plastic glass of your furnace. The light may alternatively be installed outside of your furnace, depending on the model. Call 646-836-2936 for HVAC service if you notice anything other than a constant, coloured light or a blinking green light. Your furnace could be indicating with an error code that it needs to be serviced by a professional.
Cleaning the Flame Sensor
A filthy flame sensor may be the reason your furnace tries to start but stops without producing heat. Your furnace will attempt to ignite three times when this happens before a safety function turns it off for around an hour. You can clean your flame sensor by yourself if opening your furnace makes you feel comfortable. If not, one of our heater service experts can do it for you.
Verify Your Fuel Supply
Have a go with another gas appliance. If it fail, you can run out of propane or have your natural gas service cut off.
Switch On the Pilot Light
An older furnace may have a snuffed pilot light. Use these instructions or locate the directions on a label on your furnace to relight it.
See the “pilot,” “on,” and “off” switches on the bottom of your furnace.
Plunge the switch to “off.”
To avoid maybe starting a fire, wait at least five minutes.
Turn the dial to “pilot.”
As you bring the flame of a long lighter to the pilot light opening, press the “reset” button.
Once the pilot light comes on, release the “reset” button.
If, after twice following the directions, the pilot light still won’t light or stay lit, give us a call at 646-836-2936 to arrange furnace servicing.
Our work Gallery
